View source for Screen Printing/Plastisol Ink vs Water Based Ink

== Plastisol vs Water Based Ink | ScreenPrinting.com powered by Ryonet ==

Plastisol vs Water Based Ink | ScreenPrinting.com powered by Ryonet - http://www.screenprinting.com/plastisol-vs-water-based-ink-for-textile-printing

Plastisol Ink vs Water Based Ink

There are two main types of ink that are used for textile printing. Water-based ink utilizes either dyes or pigments in a suspension with water as the solvent. The evaporation of the water is necessary to set or cure the ink. This curing can take place either at room temperature or using a forced-air dryer depending upon the specific water-based ink used and the speed or volume of production.

Plastisol ink is a PVC (Some inks are Phalide Free) based system that essentially contains no solvent at all. Along with UV ink used in graphic screen printing, it is referred to as a 100% solid ink system. Plastisol is a thermoplastic ink in that it is necessary to heat the printed ink film to a temperature high enough to cause the molecules of PVC resin and

plasticizer to cross-link and thereby solidify, or cure. The temperature at which most plastisol for textile printing cures at is in the range of 300 °F to 330°F

Both types of ink are very popular. However, for the most part, they are used in very different applications. Plastisol is the ink of choice for printing of finished goods such as T-shirts, sweatshirts, jackets, and tote bags. Water-based ink is the ink of choice for the printing of yard goods; either in piece form or on the roll. Both inks have technical advantages and disadvantages for use in specific applications. They also each have their own environmental impacts and these should be considered for the particular application and shop setup.

Advantages of Plastisol

 

*    Plastisol can best be described as a user-friendly ink because it is very easy to manage.

*    Plastisol can be left in the screen for extended periods of time without clogging the mesh. It is ready to use right out of the container more than 90% of the time. In most applications, it can be printed wet-on-wet, which allows for increased production speeds. It comes in formulations that can be printed on light and dark fabrics. And, in most municipalities, the disposal of waste plastisol is a very simple process.

*    Plastisol does not dry. In order for a compound to dry, there must be evaporation of some kind of solvent. Since plastisol has little or no solvent, it cannot dry. Because of this characteristic, plastisol can be left in screens, the lids can be left off of the ink containers (although keeping them covered is a good practice to keep lint and dirt out of the ink). And ink left at the end of the job can be returned to the container for reuse without any adverse affects. This last practice is a great benefit in reducing waste product. 

*    Plastisol is extremely versatile in that most printers never have to amend the ink. They are able to use it direct from the container without ever adjusting the viscosity or the strength.

*    Plastisol comes in strengths from transparent to very opaque and most printers will have the various versions available to use, depending upon the type and color of fabric they are printing on. The various opacities of ink also vary greatly in price with the most opaque being the most expensive, mainly due to the cost of the increased pigment. So, good shop management dictates that the proper opacity be applied to each fabric in order to be cost effective.

 

Plastisol Disadvantages

 

*    Since Plastisol is a thermoplastic, it will remelt if it comes in contact with anything hot enough. For that reason, plastisol prints cannot be ironed. If an iron touches a print, it will smear the ink.

*    Plastisol ink also creates an ink film that can be felt with the hand. The higher the opacity of the ink, the greater the hand. This heavy hand is considered a disadvantage at the consumer level. One of the most important practices when using plastisol ink is to keep the ink clean.

 

What this statement means, is that it is very beneficial, and cost effective, to keep plastisol colors from being contaminated by dirt, lint, or even other colors of ink. By maintaining clean shop practices, there will be a great reduction in ink waste. Clean ink can be returned to the original ink container for reuse. There is no degradation in the quality of plastisol as long as it is not mixed with other colors or contaminated with foreign materials.

Plastisol that has been contaminated with other colors is can still be retained in a separate container for blending with other waste ink. Often times this waste ink can be used to create new colors or, it can be over pigmented with fresh pigment to create a dark color, such as black, for use on less critical jobs.

 

With good plastisol ink management, waste can be reduced to a very small percentage. Plastisol product that is unusable is not considered hazardous waste in most municipalities as long as it is solidified (cured). The best way to achieve this cure is to heat the waste container itself to 160 °C (320 °F) for a period long enough to cure the ink all the way through. In practice, a one gallon container of plastisol will cure all the way through in approximately one hour.

 

If the plastisol needs to be disposed of in an uncured state, then hazardous chemical regulations usually apply. For either cured or uncured disposal, it is recommended that you always check with local regulatory agencies.

 

 

The biggest environmental hazard in the use of plastisol comes in the screen and equipment cleaning steps. In order to emulsify the ink for easy removal from screens, squeegees, flood bars, spatulas, and work surfaces, it is necessary to use some type of solvent. The waste ink and the solvent must be disposed of properly in order to minimize environmental impact.

The screen printing industry has been very proactive in the creation of products that can minimize the impact of these cleaning processes. Environmentally-friendly solvents, and solvents that are more environmentally sensitive than traditional petroleum-based solvents are readily availble. In addition, there are many types of filtration and cleaning systems available to capture inks and solvent residues to minimize the solids that are discharged into the sewer system.

 

Water-based Ink Systems

 

Water-based inks are defined as those that utilize water as the main solvent. That does not mean, however that water is the only solvent. It is significant to note that many water base inks contain co-solvents which may even be petroleum based solvents. The reason these co-solvents are used varies, but one of the key reasons is to decrease the time and heat necessary to cure the ink film on the fabric.

 

Advantages of Water-based Inks

 

*    Water-based inks are a good choice when a soft hand is desirable. A soft hand is the condition where the ink film cannot easily be felt with the hand when passed across the surface of the fabric. This affect is often used as an argument for why water-based is preferable to plastisol as plastisol has more of a hand than water-based.

*    Water-based ink also has the advantage of being an excellent ink system for high speed roll-to-roll yardage printing. Such printing is done on large sophisticated equipment that has very large drying (curing) capacity.

*    Water-based ink also is a good choice where ink penetration is desirable, such as in towel printing. Towels have a high nap fabric that must be printed in a manner where the ink penetrates or wicks through to the base fabric for adequate coverage. 

*    Waterbased inks that are designed to wick into the fabric are excellent for this application. Ink wicking is not a desirable affect in most other fabric printing as it will destroy the design and registration of multiple colors.

Disadvantages of Water-based Ink

 

*    Water-based ink is much more difficult to cure than plastisol. A shop that is interested in printing water-based ink must have the drying capacity to remove the water. The dryers used for water-based printing tend to be larger than those needed for plastisol. In plastisol printing, the ink film must only reach the cure temperature for a brief moment. With water-based ink, the temperature must be reached and then held until all of the solvent (water) is removed. There are water-based inks that will air dry but they are usually only acceptable for craft level printing as the room required for curing greatly reduces productivity.

*    Many water-based inks can also be more quickly cured with the addition of a catalyst that will assist the heat in the curing of the ink by continuing the cure even if all of the water is not removed in the dryer. The disadvantage of a catalyst is that once it is added to a water-based ink, it creates a time limit or pot life where the ink must be all used in a certain time or be discarded. Most catalyzed water-based ink pot lifes are between four and twelve hours. Since water-based inks contain water as an evaporative solvent, care must be taken to prevent the ink from drying in the screen. If water-based ink is left in open mesh for even a short period of time, it can clog the mesh and ruin the screen.

*    Practiced water-based ink printers must always be conscious of how long a screen sits between prints to prevent the ink from drying in. While modern water-based inks are less prone to this phenomenon, it is still a concern. In addition, when a water-based print job will take more than one day, the ink must be removed and the screen cleaned with to prevent drying. The ink is then put back in the screen on the next work day and the job is continued.

*    Water-based ink is also much more aggressive than plastisol towards the emulsion that is used to create the screen stencil. Emulsion manufacturers all make water-resistant emulsions that must be used for water-based printing. If standard emulsion is used, the water-based ink will destroy the stencil by melting the emulsion is as little as a few minutes. Even when the proper emulsion is used, screen life tends to be much less with water-based printing than it is for plastisol printing 

Water-based Ink Cleanup

There is a common misconception that because water can be used for cleaning screens, squeegees and tools, that the waste water can just be discharged in the sewer. However, the water-based ink is not just water. There are pigments, binders, thickeners, and sometimes, even co-solvents in the ink residue.

Screen cleaning systems that can at least capture the solids are still recommended. In addition, water-based that has not been catalyzed can be returned to its container for reuse. If the ink has been catalyzed, it should be considered hazardous waste unless it can be dried out (all water and solvent removed) before discarding. If it cannot be dried, it should be disposed of as hazardous waste. 

Summary

Whether printing with plastisol or a water-based ink system, you are still printing a chemical compound. Therefore, it is essential that proper handling and disposal methods be practiced. As stated above, there are advantages and disadvantages to each ink system. The key is to use the proper ink for the application, minimizing waste product, and always dispose of waste properly.


<pre>  
Type	 	Print Ease	 	Opacity 	Hand/Feel 	Curing 		Ink Recovery
Plastisol 	Easy 			Low-High 	Med-Heavy 	Easy		Easy
Water Base 	Med (Dries Fast) 	Low-Med 	Low-Med 	Med 		Easy
</pre>
 
<pre>
Usage Recommendations      Plastisol           Water-base
T-Shirts/light colors      Excellent           Excellent
T-Shirts/dark colored      Good                Poor
Nylon Jackets              Good                Poor
Towels                     Poor                Excellent
Yard goods                 Poor                Excellent
Sporting Goods             Excellent           Poor
</pre>

== plastisol ink vs water based ink | Real Thread ==

plastisol ink vs water based ink | Real Thread - https://www.realthread.com/blog/plastisol-ink-vs-water-based-ink-2014-09-11

Water Based and Discharge Ink

*    The Basics: A high end ink made for super soft shirts (commonly used in retail printing).
*    How It Works: The ink dyes the garment directly, literally removing the color of the shirt and replacing it with the color of the image.
*    Longevity: Water based prints last as long as the garment does.
*    Brightness: Water based prints are bright and true to the mock up provided by Real Thread. Pending your choice of shirt and color, certain fabric dyes will react differently to water based inks. You can see a full collection of water based approved shirts here. 
*    Feel: The water based print is super soft, breathable and literally a part of the garment. After the first wash, the print is unable to be felt on the shirt.
*    Ease of Use: Water based ink is a higher quality ink that takes significant training to use. Due to the ink dying the shirt, water based screen printers need to have significant knowledge on fabric types and ink reaction.

Plastisol Ink

*    The Basics: A plastic based ink made for apparel. This is a cheaper ink, is the industry standard and makes for thick prints.
*    How It Works: The ink lays directly on the fabric, covering the shirt with a layer of the graphic.
*    Longevity: Plastisol ink prints do eventually break down. A break down usually results in a cracked, peeled or a flaked graphic on the shirt.
*    Brightness: Plastisol ink prints are bright and true to the design.
*    Feel: Plastisol ink prints feel thick, heavy and do not allow any breathability.
*    Ease of Use: Plastisol ink was chemically formed to be highly easy to use for screen printers. The compounds allow for the ink to last indefinitely and coat any shirt.

== Water Based Ink vs Plastisol - ooShirts.com ==

Water Based Ink vs Plastisol - ooShirts.com - http://www.ooshirts.com/guides/Water-Based-Ink-vs-Plastisol.html

Water-Based Inks

How They Work: Water-based is a specialty ink for direct to garment digital printing. It is a mixture of water with dye or pigment. The water acts as the main solvent to keep the pigment or dye in liquid form but sometimes co-solvents are used as well. The purpose of the co-solvents ranges, but they are most commonly used to decrease the time and heat necessary for curing. For the print to be cured, the water has to have completely evaporated. The ink sinks into the fibers of shirt, becoming part of the fabric.

Advantages of Water-Based Inks

*    Better for the environment
*    Softer hand (ie print is thinner)
*    More breathable
*    Inks becomes part of the shirt instead of sitting on top
*    Good for creating a "vintage" look 

Disadvantages of Water-Based Inks

*    Influenced by the color of the shirt, making prints on dark garments problematic
*    More time-consuming to work with
*    Can dry in screens and clog them
*    More expensive

Plastisol

How It Works: Plastisol is the standard, economical ink to use for screenprinting. It is easy to use because it is essentially plastic. To be more specific, it is made of polyvinyl chloride (PVC) particles and and plasticizer. PVC is a commonly-used plastic that is made fluid and flexible through combination with plasticizer, which is an additive that keeps the PVC particles from clumping together or settling. Plastisol has to reach a temperature of around 350 degrees Fahrenheit for curing. Once dry, most plastisol prints sit on top of the material of the shirt.

Advantages of Plastisol

*        Inexpensive
*        Great opacity, can be used on dark garments
*        Doesn't require a source of running water
*        Won't clog screens as it won't dry until cured (requiring 350-degree heat)

Disadvantages of Plastisol

*        Thicker hand
*        Less breathable
*        Can bunch around seams