ICX

Ruckus / Brocade Switches

See Ruckus

Connect

Connect on Linux

# apt install tio
tio -b 9600 /dev/ttyS0
tio -b 9600 /dev/ttyUSB0

# apt install minicom
minicom -b 9600 -D /dev/ttyS0
minicom -b 9600 -D /dev/ttyUSB0

Connect on Windows

Use Tera Term or Putty and connect to COMX with Baud 9600

CLI

Show Config

sh run

All but "show config" will need "enable"

>enable

Interfaces

Show Interfaces

sh int bri

Show specific port:

show int eth 1/1/1

Show management port:

sh int bri | begin mgmt

IP

Show IP:

show ip

License

Show licenses:

sh license

Pagination

>enable

to skip pagination:

skip
# or skip-page-display
  Disable page display mode

to page:

page
  Enable page display mode

Ping

ping [IP]

POE

Enable POE:

conf t
 interface eth 1/1/1
  inline power

Disable POE:

conf t
 interface eth 1/1/1
  no inline power

Show Interface POE:

show inline power

Show Interface POE details: (and firmware version)

show inline power details

Limit POE on interface:

int ent ethernet 1/1/1 to 1/1/48
  inline power
  inline power power-limit 25000

Reboot Switch

reload

SSH

Enable SSH:

## Generate keys
crypto key generate dsa
# Add admin user:
username admin pri 0 password [PASSWORD]
# enable 
aaa authentication login default local

Disable SSH:

crypto key zeroize
crypto key zeroize dsa

Version

Show switch version and model and serial:

show version
sh ver

Example:

>sh ver
...
    UNIT 1: compiled on Mar  2 2012 at 12:38:17 labeled as ICX64S07400
                (10360844 bytes) from Primary ICX64S07400.bin
        SW: Version 07.4.00T311
  Boot-Monitor Image size = 512, Version:07.4.00T310 (kxz07400)
  HW: Stackable ICX6450-48-HPOE
==========================================================================
UNIT 1: SL 1: ICX6450-48p POE 48-port Management Module
         Serial  #: BZTXXXXXXXX
         License: BASE_SOFT_PACKAGE   (LID: dbvHKIFjFox)
...

VLANs

Show VLANs:

show vlan

Config

Configure:

enable
configure terminal
# or conf t

Show Config:

show config
sh run

Write Config:

write mem

Clear Config:

erase startup-config

DHCP Client

Management Interface DHCP Client

dhcp ip

ip dhcp-client enable
ip dhcp-client auto-update enable
no ip dhcp-client enable

Static IP

ip address 10.10.10.104/24
# or
ip address 10.10.10.104 255.255.255.0

ip default-gateway 10.10.10.1
no ip dhcp-client auto-update enable
no ip dhcp-client enable

Show IP:

show ip

Interface

sh int bri

Show specific port:

show int eth 1/1/1

Show management port:

sh int bri | begin mgmt

Disable Interface

int eth 1/1/48
  disable
  enable

Spanning Tree

Disable Spanning Tree On specific port:

interface ethernet 1/1/1
 loop-detection
 no spanning-tree
!

VLAN

Show VLANs:

show vlan

Clear VLAN:

no vlan [#]

Hostname

hostname [name]

Users

enable super-user-password [PASSWORD]
no enable super-user-password

username admin [PASSWORD]
no username admin

Reset Password

As switch boots up, when you see the following, press 'b':

Enter 'b' to stop at boot monitor:

then type "no password":

no password

then type "boot" to continue booting:

boot
# or boot_primary

Then either change password

enable
conf t