ICX

Ruckus / Brocade Switches

See Ruckus

Connect

Connect on Linux

# apt install tio
tio -b 9600 /dev/ttyS0
tio -b 9600 /dev/ttyUSB0

# apt install minicom
minicom -b 9600 -D /dev/ttyS0
minicom -b 9600 -D /dev/ttyUSB0

Connect on Windows

Use Tera Term or Putty and connect to COMX with Baud 9600

CLI

Show Config

sh run

All but "show config" will need "enable"

>enable

Interfaces

Show Interfaces

sh int bri

Show specific port:

show int eth 1/1/1

Show management port:

sh int bri | begin mgmt

IP

Show IP:

show ip

License

Show licenses:

sh license

Pagination

>enable

to skip pagination:

skip
# or skip-page-display
  Disable page display mode

to page:

page
  Enable page display mode

Ping

ping [IP]

POE

Enable POE:

conf t
 interface eth 1/1/1
  inline power

Disable POE:

conf t
 interface eth 1/1/1
  no inline power

Show Interface POE:

show inline power

Show Interface POE details: (and firmware version)

show inline power details

Limit POE on interface:

int ent ethernet 1/1/1 to 1/1/48
  inline power
  inline power power-limit 25000

Reboot Switch

reload

SSH

Enable SSH:

## Generate keys
crypto key generate dsa
# Add admin user:
username admin pri 0 password [PASSWORD]
# enable 
aaa authentication login default local

Disable SSH:

crypto key zeroize
crypto key zeroize dsa

Version

Show switch version and model and serial:

show version
sh ver

Example:

>sh ver
...
    UNIT 1: compiled on Mar  2 2012 at 12:38:17 labeled as ICX64S07400
                (10360844 bytes) from Primary ICX64S07400.bin
        SW: Version 07.4.00T311
  Boot-Monitor Image size = 512, Version:07.4.00T310 (kxz07400)
  HW: Stackable ICX6450-48-HPOE
==========================================================================
UNIT 1: SL 1: ICX6450-48p POE 48-port Management Module
         Serial  #: BZTXXXXXXXX
         License: BASE_SOFT_PACKAGE   (LID: dbvHKIFjFox)
...

VLANs

Show VLANs:

show vlan

Config

Configure:

enable
configure terminal
# or conf t

Show Config:

show config
sh run

Write Config:

write mem

Clear Config:

erase startup-config

DHCP Client

Management Interface DHCP Client

dhcp ip

ip dhcp-client enable
ip dhcp-client auto-update enable
no ip dhcp-client enable

Static IP

ip address 10.10.10.104/24
# or
ip address 10.10.10.104 255.255.255.0

ip default-gateway 10.10.10.1
no ip dhcp-client auto-update enable
no ip dhcp-client enable

Show IP:

show ip

Interface

sh int bri

Show specific port:

show int eth 1/1/1

Show management port:

sh int bri | begin mgmt

Disable Interface

int eth 1/1/48
  disable
  enable

Spanning Tree

Disable Spanning Tree On specific port:

interface ethernet 1/1/1
 loop-detection
 no spanning-tree
!

VLAN

Show VLANs:

show vlan

Clear VLAN:

no vlan [#]

Hostname

hostname [name]

Users

enable super-user-password [PASSWORD]
no enable super-user-password

username admin [PASSWORD]
no username admin

Privilege Levels

3 privileged levels:

1. super-user-password [PASSWORD]] - Super-user level password
2. port-config-password [PASSWORD]] - Port level configuration password
3. read-only-password [PASSWORD]] - Read-only level password

• Super User level - Allows complete read-and-write access to the system. This is generally for system administrators and is the only management privilege level that allows you to configure passwords.
• Port Configuration level - Allows read-and-write access for specific ports but not for global (system-wide) parameters.
• Read-only level - Allows access to the Privileged EXEC mode and User EXEC mode of the CLI but only with read access.

Reset Password

As switch boots up, when you see the following, press 'b':

Enter 'b' to stop at boot monitor:

then type "no password":

no password

then type "boot" to continue booting:

boot
# or boot_primary

Then either change password

enable
conf t