ICX
Ruckus / Brocade Switches
See Ruckus
Connect
Connect on Linux
# apt install tio tio -b 9600 /dev/ttyS0 tio -b 9600 /dev/ttyUSB0
# apt install minicom minicom -b 9600 -D /dev/ttyS0 minicom -b 9600 -D /dev/ttyUSB0
Connect on Windows
Use Tera Term or Putty and connect to COMX with Baud 9600
CLI
Show Config
sh run
All but "show config" will need "enable"
>enable
Interfaces
Show Interfaces
sh int bri
Show specific port:
show int eth 1/1/1
Show management port:
sh int bri | begin mgmt
IP
Show IP:
show ip
License
Show licenses:
sh license
Pagination
>enable
to skip pagination:
skip # or skip-page-display Disable page display mode
to page:
page Enable page display mode
Ping
ping [IP]
POE
Enable POE:
conf t interface eth 1/1/1 inline power
Disable POE:
conf t interface eth 1/1/1 no inline power
Show Interface POE:
show inline power
Show Interface POE details: (and firmware version)
show inline power details
Limit POE on interface:
int ent ethernet 1/1/1 to 1/1/48 inline power inline power power-limit 25000
Reboot Switch
reload
SSH
Enable SSH:
## Generate keys crypto key generate dsa # Add admin user: username admin pri 0 password [PASSWORD] # enable aaa authentication login default local
Disable SSH:
crypto key zeroize crypto key zeroize dsa
Version
Show switch version and model and serial:
show version sh ver
Example:
>sh ver
...
UNIT 1: compiled on Mar 2 2012 at 12:38:17 labeled as ICX64S07400
(10360844 bytes) from Primary ICX64S07400.bin
SW: Version 07.4.00T311
Boot-Monitor Image size = 512, Version:07.4.00T310 (kxz07400)
HW: Stackable ICX6450-48-HPOE
==========================================================================
UNIT 1: SL 1: ICX6450-48p POE 48-port Management Module
Serial #: BZTXXXXXXXX
License: BASE_SOFT_PACKAGE (LID: dbvHKIFjFox)
...
VLANs
Show VLANs:
show vlan
Config
Configure:
enable configure terminal # or conf t
Show Config:
show config sh run
Write Config:
write mem
Clear Config:
erase startup-config
DHCP Client
Management Interface DHCP Client
dhcp ip
ip dhcp-client enable ip dhcp-client auto-update enable no ip dhcp-client enable
Static IP
ip address 10.10.10.104/24 # or ip address 10.10.10.104 255.255.255.0
ip default-gateway 10.10.10.1 no ip dhcp-client auto-update enable no ip dhcp-client enable
Show IP:
show ip
Interface
sh int bri
Show specific port:
show int eth 1/1/1
Show management port:
sh int bri | begin mgmt
Disable Interface
int eth 1/1/48 disable enable
Spanning Tree
Disable Spanning Tree On specific port:
interface ethernet 1/1/1 loop-detection no spanning-tree !
VLAN
Show VLANs:
show vlan
Clear VLAN:
no vlan [#]
Hostname
hostname [name]
Users
enable super-user-password [PASSWORD] no enable super-user-password
username admin [PASSWORD] no username admin
Reset Password
As switch boots up, when you see the following, press 'b':
Enter 'b' to stop at boot monitor:
then type "no password":
no password
then type "boot" to continue booting:
boot # or boot_primary
Then either change password
enable conf t