ICX

Ruckus / Brocade Switches

See Ruckus

Connect

Connect on Linux

# apt install tio
tio -b 9600 /dev/ttyS0
tio -b 9600 /dev/ttyUSB0

# apt install minicom
minicom -b 9600 -D /dev/ttyS0
minicom -b 9600 -D /dev/ttyUSB0

Connect on Windows

Use Tera Term or Putty and connect to COMX with Baud 9600

CLI

Show Config

sh run

All but "show config" will need "enable"

>enable

Interface Show

Show Interfaces

sh int bri

Show specific port:

show int eth 1/1/1

Show management port:

sh int bri | begin mgmt

License

Show licenses:

sh license

Logs

Show logs:

sh log

Clear logs:

clear log

Sample:

Syslog logging: enabled ( 0 messages dropped, 1 flushes, 0 overruns)
    Buffer logging: level ACDMEINW, 0 messages logged
    level code: A=alert C=critical D=debugging M=emergency E=error
                I=informational N=notification W=warning

Dynamic Log Buffer (50 lines):
Jan  1 12:19:30:I:Security: SSH login by myuser from src IP 10.10.10.10 from src MAC xxxx.xxxx.xxxx to USER EXEC mode using RSA as Server Host Key.
Jan  1 00:00:57:I:STP: VLAN 1 Port 1/1/30 STP State -> FORWARDING (FwdDlyExpiry)
Jan  1 00:00:55:I:STP: VLAN 1 Port 1/1/48 STP State -> LEARNING (FwdDlyExpiry)

Management IP Show

Show IP:

show ip

Pagination

>enable

to skip pagination:

skip
# or skip-page-display
  Disable page display mode

to page:

page
  Enable page display mode

Ping

ping [IP]

POE

Enable POE:

conf t
 interface eth 1/1/1
  inline power

Disable POE:

conf t
 interface eth 1/1/1
  no inline power

Show Interface POE:

show inline power

Show Interface POE details: (and firmware version)

show inline power details

Limit POE on interface:

int ent ethernet 1/1/1 to 1/1/48
  inline power
  inline power power-limit 25000

Reboot Switch

reload

Version

Show switch version and model and serial:

show version
sh ver

Example:

>sh ver
...
    UNIT 1: compiled on Mar  2 2012 at 12:38:17 labeled as ICX64S07400
                (10360844 bytes) from Primary ICX64S07400.bin
        SW: Version 07.4.00T311
  Boot-Monitor Image size = 512, Version:07.4.00T310 (kxz07400)
  HW: Stackable ICX6450-48-HPOE
==========================================================================
UNIT 1: SL 1: ICX6450-48p POE 48-port Management Module
         Serial  #: BZTXXXXXXXX
         License: BASE_SOFT_PACKAGE   (LID: dbvHKIFjFox)
...

VLAN Show

Show VLANs:

show vlan

Config

Configure:

enable
configure terminal
# or conf t

Show Config:

show config
sh run

Write Config:

write mem

Clear Config:

erase startup-config

Hostname

hostname [name]

Interface

sh int bri

Show specific port:

show int eth 1/1/1

Show management port:

sh int bri | begin mgmt

Disable Interface

int eth 1/1/48
  disable
  enable

IP

Management Interface DHCP Client

dhcp ip

ip dhcp-client enable
ip dhcp-client auto-update enable
no ip dhcp-client enable

Static IP

ip address 10.10.10.104/24
# or
ip address 10.10.10.104 255.255.255.0

ip default-gateway 10.10.10.1
no ip dhcp-client auto-update enable
no ip dhcp-client enable

Show IP:

show ip

SFP

GBIC

# show media
...
Port 1/3/1:  Type  : EMPTY
Port 1/3/2:  Type  : EMPTY
Port 1/3/3:  Type  : 1G M-TX(SFP)
Port 1/3/4:  Type  : EMPTY

# sh media et 1/3/3
Port   1/3/3: Type  : 1G M-TX(SFP)
             Vendor: XXX    Version: D1
             Part# : SFP-1000BASE-TX    Serial#: XXX

# sh int bri
..
1/3/3      Up      Forward Full 1G    None  No  1    0   xxxx.xxxx.xxxx

#sh int et 1/3/3
10GigabitEthernet1/3/3 is up, line protocol is up

Note: If a 1-Gbps optic transceiver is inserted, you must configure the port using the speed-duplex 1000-full-master command at the interface level.

Enable port:

# conf term
# int ethernet 1/3/3
# speed-duplex 1000-full-master

or short form:

config t
int e 1/2/1
speed 1000-full

# sh run
...
stack unit 1
  module 1 icx7150-48pf-poe-port-management-module
  module 2 icx7150-2-copper-port-2g-module
  module 3 icx7150-4-sfp-plus-port-40g-module
  stack-port 1/3/1
  stack-port 1/3/3
!
interface ethernet 1/3/3
 speed-duplex 1000-full
!

10GE SFP+

• 10GE SR 300m ((SFP+))
• 10GE USR 100m (SFP +)

Spanning Tree

Disable Spanning Tree On specific port:

interface ethernet 1/1/1
 loop-detection
 no spanning-tree
!

SSH

Show ssh config settings:

sh ip ssh config

> sh ip ssh config
...
SSH server                 : Enabled
SSH port                   : tcp\22
Host Key                   : DSA 1024,  RSA 1024
Encryption                 : aes256-cbc, aes192-cbc, aes128-cbc, aes256-ctr, aes192-ctr, aes128-ctr, 3des-cbc
...
Authentication methods     : Password, Public-key, Interactive
...

Enable SSH:

## Generate keys
crypto key generate rsa
  # ^ Their offer: ssh-rsa
crypto key generate dsa
  # ^ Their offer: ssh-dss
# Add admin user:
username admin pri 0 password [PASSWORD]
# enable 
aaa authentication login default local

Disable SSH:

crypto key zeroize
crypto key zeroize dsa

Note, the ICX uses really old key exchange method 'diffie-hellman-group1-sha1'

debug1: kex: algorithm: diffie-hellman-group1-sha1
debug1: kex: host key algorithm: ssh-rsa
# or
debug1: kex: host key algorithm: ssh-dss
debug1: kex: server->client cipher: aes128-ctr MAC: hmac-sha1 compression: none
debug1: kex: client->server cipher: aes128-ctr MAC: hmac-sha1 compression: none

To allow diffie-hellman-group1-sha1, edit either .ssh/config(to host) or /etc/ssh/ssh_config and add the following:

# ICX SSH
KexAlgorithms +diffie-hellman-group1-sha1
HostKeyAlgorithms +ssh-dss,ssh-rsa
PubkeyAcceptedKeyTypes +ssh-dss,ssh-rsa

NOTE: If you want to have the switch connect in reverse to do firmware updates, make sure to add the same to /etc/ssh/sshd_config

# Allow Legacy ICX switches to connect
KexAlgorithms +diffie-hellman-group1-sha1
HostKeyAlgorithms +ssh-dss,ssh-rsa

## PubkeyAcceptedKeyTypes +ssh-dss,ssh-rsa # icx doesn't have a private key option - sadness

Public Keys

• Note: The public key file may contain up to 16 DSA or RSA key pairs.
• Note: Each key in the public key must be in exactly this format (remove the ssh-rsa prefix, the 'Comment' line is optional):
• Note: Use a 2048 bit key (ssh-keygen -b 2048). The larger key will generate connect issues for 6450s (probably 7150s too). (no key from blob. pkalg ssh-rsa: invalid format)

ssh-keygen -b 2048

---- BEGIN SSH2 PUBLIC KEY ---- 
Comment:  "2048-bit RSA, converted from OpenSSH"
AAAAB3NaC1yc2EAAAABIwAAAQEA0pt94yJmKwPfPZnxxYSS1aVaaqWgRM79EfRXf2XUrs
834hx881MmQedye1oJrntvA8LyVUIepOdbc874i4259mtSXx+cfZW0/QeJggT/1zE82+n
w706gGqNsE+XsT12bi6KU4Al2IWULce74yfQY9/amy38ZPCesKKurH4+2m/Ba69391lp
nJ0BIQidn+I8hARUGayrOTrx/e2^kdC+2aNh6mS17KDiRyj8WBV3F5z5f5rlYBL/WoJ2beo
R3L6H6wHXP8dZ1F4IqeVxeIimkFTzMEE*r/wHCnhewetnDy3iJAgr0TXTicJ1Qpb1MCBkB
XaynjuDYSf4Kmgn8znaQ==
---- END SSH2 PUBLIC KEY ----

Copy the combined key file (up to 16 keys) to tftp server, and have the ICX pull and override keyfile with:

conf term
 ip ssh pub-key-file tftp [TFTP_IP] [PATH/keyfile.txt]

List keys:

show ip client-pub-key

Remove pub key file:

ip ssh pub-key-file remove

VLAN

Show VLANs:

show vlan

Clear VLAN:

no vlan [#]

Time

Daylight Saving (Summer Time)

clock summer-time zone us pacific start 02-28-21 02:00:00 end 10-30-21 02:00:00 offset 60

Note: Will have to be manually updated each year.

Users

Add Users:

username admin password [PASSWORD]
no username admin

username myuser privilege [LEVEL] password [PASSWORD]
# LEVEL:   <0 READ-WRITE, 4 PORT-CONFIG, 5 READ-ONLY> User privilege level

Require Login:

aaa authentication web-server default local
aaa authentication login default local

Configure seperate enable privilege passwords:

enable super-user-password [PASSWORD]
enable port-config-password [PASSWORD]
enable read-only-password [PASSWORD]

no enable super-user-password

Enter enable mode:

enable

Show who logged in as:

sh who

Privilege Levels

3 privileged levels:

1. enable super-user-password [PASSWORD]] - Super-user level password
2. enable port-config-password [PASSWORD]] - Port level configuration password
3. enable read-only-password [PASSWORD]] - Read-only level password

• Super User level - Allows complete read-and-write access to the system. This is generally for system administrators and is the only management privilege level that allows you to configure passwords.
• Port Configuration level - Allows read-and-write access for specific ports but not for global (system-wide) parameters.
• Read-only level - Allows access to the Privileged EXEC mode and User EXEC mode of the CLI but only with read access.

Firmware

Select Boot Slot

Show boot configuration:

ICX7450 #sh boot-preference
Boot system preference(Configured):
        Use Default

Boot system preference(Default):
        Boot system flash primary
        Boot system flash secondary

Select second boot slot:

ICX7450# Boot system flash secondary

Show boot configuration after change:

ICX7450# sh boot-preference
Boot system preference(Configured):
        Boot system flash secondary

Boot system preference(Default):
        Boot system flash primary
        Boot system flash secondary

Show configuration:

ICX7450# sh run
Current configuration:
!
...
!
boot sys fl sec

Reset Password

As switch boots up, when you see the following, press 'b':

Enter 'b' to stop at boot monitor:

then type "no password":

no password

then type "boot" to continue booting:

boot
# or boot_primary

Then either change password

enable
conf t